Отзывы epson expression home xp-420

Характеристики

How do I change the ink cartridges?

• Do the following:

  Removing and Installing Ink Cartridges
  

  Make sure you have your replacement cartridges handy before you begin. You must install new cartridges immediately after removing the old ones.

  Caution: Leave your old cartridges in the printer until you are ready to replace them to prevent the print head nozzles from drying out. Do not open ink cartridge packages until you are ready to install the ink. Cartridges are vacuum packed to maintain reliability.

  1. Turn on your product.
  2. Lift up the scanner unit.

     Caution: Do not move the print head by hand; otherwise, you may damage your product. Do not touch the flat white cable inside the printer.

  3. Squeeze the tab on the cartridge and lift the cartridge straight up to remove it.

     Note: Dispose of used cartridges carefully. Do not take the used cartridge apart or try to refill it.

     Warning: If ink gets on your skin, wash it thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water. If ink gets into your mouth, spit it out and see a doctor right away. Keep ink cartridges out of the reach of children.

  4. Before opening the new cartridge package, shake it gently four or five times.

     Caution: Do not shake the cartridges after opening the packages, or ink may leak.

  5. Remove the cartridge from the package.

     Caution: Do not touch the green chip on the cartridge. Install the new cartridge immediately after removing the old one; if you do not, the print head may dry out and be unable to print.

  6. Remove the yellow tape from the side of the cartridge.

     Caution: Do not remove any other labels or seals, or ink will leak.

  7. Insert the new cartridge into the holder and push it down until it clicks into place.
  8. Lower the scanner unit and press the  start button.
     The print head moves to its home position and the printer starts charging the ink. This takes about 90 seconds. When you see a confirmation message on the screen, ink charging is finished.

     Caution: Never turn off the product while the power light is flashing or you will waste ink.

     If you see an error screen telling you an ink cartridge is installed incorrectly, lift up the scanner unit and press the ink cartridge down until it clicks into place. When you’re finished, press the OK button.

  If you remove a low or expended ink cartridge, you cannot re-install and use the cartridge.

  Caution: If you remove an ink cartridge for later use, protect the ink supply area from dirt and dust and store it in the same environment as the printer. The valve in the ink supply port is designed to contain any excess ink, but do not touch the ink supply port or surrounding area. Always store ink cartridges with the label facing up; do not store cartridges upside-down.

  Related conceptsPurchase Epson Ink Cartridges

Published:  Mar 3, 2015
Was this helpful​? Thank you for the feedback!

I was able to print from my Mac before with a wireless connection, but now I can’t. What should I do?

• The problem can be caused by your printer, computer, or wireless network. Do the following:

  1. To determine if the printer can print without a computer, print a nozzle check pattern from the product’s control panel.
     • If you can print, go to the next step.
     • If you can’t print a nozzle check pattern, check the product’s LCD for error messages. Clear any errors displayed on the LCD, then try printing a nozzle check pattern again. If you still can’t print, contact Epson support.
  2. Delete any pending print job(s) from the Epson print queue and then try printing again.
     • If you can print now, you’re done, and you can skip the remaining steps.
     • If you can’t print, go to the next step.
  3. In the Print & Scan, Print & Fax, or Printers & Scanners window, select your printer, then click — to remove the printer. Click +, select your printer, and click Add to add the printer back on the printer queue. Then try printing again.

     If you can print now, you’re done, and you can skip the remaining steps.

     If you still can’t print, check the Wi-Fi icon on the product’s control panel, then do one of the following:

     • If the Wi-Fi icon is displayed, follow the instructions in the Initialize Your Router and Restart Your Computer section below.
     • If the Wi-Fi icon is displayed, follow the instructions in the Reinstall the Product Software section below.

  Initialize Your Router and Restart Your Computer

  1. Unplug your router’s power cord from the power outlet, wait a brief period, then plug it back in. Try to print. You may need to re-establish the connection for the other devices on your network.
  2. If you can print, you’re done. The problem was resolved by initializing your router.

     If you still can’t print, restart your computer, then try printing again. If these steps do not resolve your problem, contact Epson support.

  Reinstall the Product Software

  Important: You’ll need to know your network name (SSID) and network password before you can set up your product. If you don’t know them, contact the manufacturer of your router or the person who set up your network. If you are using a 5 GHz wireless router, set the router to operate in dual band (2.4 GHz and 5 GHz) mode. See your router documentation for instructions.

  1. Reset the product’s Wi-Fi settings on the product’s control panel by doing the following:

     Press the home button, if necessary. Press the arrow buttons to select Setup and press OK. Select Restore Default Settings and press OK. Select Network Settings, press OK, then select Yes.

  2. On your Mac, open the menu and select System Preferences. Then click either Security & Privacy or Security. Select the Firewall tab, then disable the firewall.

     If you have other firewall software enabled, you’ll also need to disable it. If you don’t know how to disable it, contact your firewall provider for help.

     Note: This step is needed to install the product’s software and complete the Wi-Fi setup. Remember to enable your firewall software after you complete the Wi-Fi setup.

  3. Unplug your router’s power cord from the power outlet, wait a brief period, then plug it back in. You may need to re-establish the connection for the other devices on your network.
  4. Download the Drivers and Utilities Combo Package from the Downloads tab for your product.

     Note: Make a note of the file name and save the location so you can retrieve it.

  5. Open the file you downloaded and follow the on-screen instructions. When you see the Select Your Connection screen, select Wireless connection, click Continue, then follow the on-screen instructions.
  6. When you see the Select Setup Option screen, select Set up printer for the first time, click Continue, then follow the on-screen instructions to complete the installation. If you see this screen, click Options.

     After you complete the Wi-Fi setup, remember to enable your firewall. If these troubleshooting instructions did not solve the problem, please contact Epson support.

Published:  Mar 3, 2015
Was this helpful​? Thank you for the feedback!